27 products found for "Walther"

Standard grip, according ISSF rules, stippled and oiled, for Walther CP2. With adjustable palm rest, moveable 5mm up and down from the middle position!For the "old" CP2 with a black housing of 48mm height (measured under the rear sight).If your CP2 has a silvery housing of 43mm height, you have to choose this version!

Standard grip, according ISSF rules, stippled and oiled, for Walther CSP, Haemmerli Xesse, Trailside. With adjustable palm rest, moveable 5mm up and down from the middle position! 

for attaching the grip to the Walther LP400/LP500 or Haemmerli AP20 with "memory function", including the lateral attachment screw.Allows 3D panning of the grip, with the position remaining "saved".

for grip mounting from below (more stable). Needed if you want to attach your GSP grip with a screw from below, instead of the two lateral screws. Conditions:- corresponding hole below in the frame- lower frame thickness is 16mmAttention: Check the screw length for your grip (there are different variants). A screw that is too long can damage the frame!

Standard grip, according ISSF rules, stippled and oiled, for Walther LP300, LP300XT. With adjustable palm rest, moveable 5mm up and down from the middle position!Grip angle is adjustable (like original).If you have the LP300 Club version without 3D-ball-joint, you have to order this version: PA10/ LP300 Club

Standard grip, according ISSF rules, stippled and oiled, for Walther GSP from 1970 until 1976 and for newer US versions with safety. With adjustable palm rest, moveable 5mm up and down from the middle position! For GSP with safety and a lower frame thickness of 16mm. The grip will be fixed with two lateral screws. It can also be fixed with one screw from below (holds better). For it you need the original fixing part (see photos and below). The fixing part of the Nill Company will NOT FIT!Here you will find all GSP versions built before 2022!

Standard grip, according ISSF rules, stippled and oiled, for Walther FP with electronic trigger. With adjustable palm rest, moveable 5mm up and down from the middle position!The fitting fore-end can't be manufactured.

Standard grip, according ISSF rules, stippled and oiled, for Walther SSP, SSPe. With adjustable palm rest, moveable 5mm up and down from the middle position! Swivelling, like original. The grip angle will be fixed additional with four grub screws.Attention: Do not tighten the lateral grub screws firmly, but only slightly turn them on contact! The grip mounting happens, with a socket-nut from behind.The same grip with a steeper angle (like GSP) you'll find here.

Standard grip, according ISSF rules, stippled and oiled, for Walther GSP500, steep version. With adjustable palm rest, moveable 5mm up and down from the middle position! The grip angle of this version is 5° steeper than the original grip. Good for shooters who want the steep angle of the old GSP.The same grip with a more flat angle (like original) you'll find here.

Standard grip, according ISSF rules, stippled and oiled, for Walther LP200plus with ball-and-socket joint. With adjustable palm rest, moveable 5mm up and down from the middle position!Grip angle is adjustable (like original).Only for LP200 or LP201 with ball-and-socket joint. If your pistol doesn't have this, you should choose the normal LP200 version.

Standard grip, according ISSF rules, stippled and oiled, for Walther LP200, LP201, CPM1, LPM1, CP3, CP2Match. With adjustable palm rest, moveable 5mm up and down from the middle position!For non-pivoting grip mounting only. If your pistol has a ball-and-socket joint, you would have to choose the LP200plus version!

Standard grip, according ISSF rules, stippled and oiled, for Tesro PA10, PA10-2, PA10 pro, Walther LP300 Club. With adjustable palm rest, moveable 5mm up and down from the middle position!The PA10 grip can be swivelled, like original. From the original grip you have to use the aluminium plate.The LP300-club can't be swivelled and it is a aluminium cylinder.